Once the funnel is in desired position, retighten the screw with Phillips-head screwdriver.With screw loosened, apply tabs to position funnel in one of the two positions by either pushing down or upward depending on desired position.With a Phillips-caput screwdriver, loosen screw.ADJUSTING FUNNEL HEIGHT To adapt funnel height: – Consult the dealer or an experienced radio/Television set technician for help. – Connect the equipment into an outlet on a excursion different from that to which the receiver is connected. – Increase the separation between the equipment and receiver. – Reorient or relocate the receiving antenna. If this equipment does cause harmful interference to radio or tv set reception, which can be determined by turning the equipment off and on, the user is encouraged to endeavor to correct the interference by one or more of the following measures: Notwithstanding, there is no guarantee that interference will non occur in a item installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. These limits are designed to provide reasonable protection confronting harmful interference in a residential installation. Note: This equipment has been tested and institute to comply with the limits for a Course B digital device, pursuant to part 15 of the FCC Rules. Performance is subject field to the following two weather: (one) This device may not cause harmful interference, and (ii) this device must accept any interference received, including interference that may cause undesired operation.įor devices canonical nether Part 15, the user's transmission or instruction manual for an intentional or unintentional radiator shall circumspection the user most changes or modifications to the device (Section 15.21). This device complies with part 15 of the FCC Rules. Afterwards a five 2nd countdown, the test volition commence. Press RIGHT or LEFT to select desired motor speed. Press Upward or Downward to set the Exam Duration. The Test duration will appear (this volition be the same as the duration equally Feed Timer 1). Press the TEST button to enter the Examination Way. Exam FEEDER: Press the BACK push to reach the Main Bill of fare.When the Feed Timer is blinking at the top of the screen, printing Program or Correct to advance to the next feed Press Programme or BACK to return to the Feed Timer. Printing RIGHT or LEFT to select the desired motor setting. Ready MOTOR SPEED: Press Up or Downwardly until the motor speed setting is flashing at the lesser of the screen.Press Plan or Back to render to the Feed Timer. Press Upwardly or DOWN to prepare desired feed duration. Fix RUN DURATION: Printing Down and LEFT until the RUN Duration seconds are flashing.PROGRAM or Back to return to the Feed Timer. Once all desired days are selected, press Press DOWN to disable the selected 24-hour interval. Printing LEFT or RIGHT to highlight the desired day. Gear up DAYS OF THE Week: After setting the feed time, press Upwards so the days of the week starting time flashing.The factory settings include two feeder times 7am and 6pm, each for 6 seconds. Press Program or Dorsum to return to the Feed Timer. Press the Right push to go over to the minutes. Press the DOWN button until the feed time is flashing. Gear up FEED TIME: Press the Programme button until the desired Feed Timer appears at the top of the screen.Printing BACK to return to the Primary Bill of fare, or press Program to go along through the settings. Printing Upward or Downward to select the amount of feed you have in the feeder. FEED REMAINING: Printing the Program push button until the Est. Press BACK to return to the Main Bill of fare, or press Programme to proceed through the settings Press LEFT or RIGHT to select the electric current 24-hour interval. Prepare Current Twenty-four hours: Press the Programme button until the Set Current Day screen appears.Notation: The timer is capable up to 10 feed times, each 1-60 seconds each, and each can operate on any day of the calendar week where each twenty-four hours can be toggled ON/OFF. Press the BACK button to return to the Main Menu, or press PROGRAM to proceed through the settings Press Upwards or DOWN to set the minutes. Press Upwardly or DOWN to set the hour, then press RIGHT to become to the minutes. SET Electric current Time: Press the Programme button and SET CURRENT TIME volition appear.Please contact us at Permit united states to better serve you past activating your i-year warranty online at. If you should accept any questions near this product or whatsoever other Moultrie product, Delight read this sheet before operating the unit. Thanks for your purchase of a Moultrie Pro Hunter Two Feeder Kit. Instructions for Pro Hunter II Feeder Kit MOULTRIE MFG-13448 Pro Hunter 2 Feeder Kit Pedagogy Manual
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |